[Nov 04, 2023] Pass Your ACP-01101 Dumps Free Latest Autodesk Practice Tests
Get Top-Rated Autodesk ACP-01101 Exam Dumps Now
Autodesk ACP-01101 certification exam is a globally recognized certification that is highly valued by employers in the CAD industry. Autodesk Certified Professional: AutoCAD for Drafting and Design certification demonstrates the candidate's ability to work with AutoCAD software effectively and efficiently, which is essential for success in drafting and design fields. Autodesk Certified Professional: AutoCAD for Drafting and Design certification also signifies that the candidate has a good understanding of AutoCAD's best practices and can apply them to real-world scenarios.
NEW QUESTION # 28
You have a simple polyline selected that consists of li Select whether each statement is True or False.
Answer:
Explanation:
* FalseYou cannot convert an arc to a line by hovering over the center grip of the arc segment. You need to convert the arc to a polyline first, then use the FLATTEN command, and answer YES to remove hidden lines. Then you can explode the polyline to get line segments.
https://forums.autodesk.com/t5/autocad-forum/autocad-is-it-possible-to-convert-an-arc-to-a-segemented-li
* Falseyou can edit the polyline width by hovering over certain grips if they are vertex grips or midpoint grips. However, if they are arc segment grips, you cannot edit the width by hovering over them1.
Therefore, the statement is false.
https://knowledge.autodesk.com/support/autocad/learn-explore/caas/CloudHelp/cloudhelp/2015/ENU/Auto
* Falseyou can add a new vertex by hovering over certain grips if they are edge grips or midpoint grips. However, if they are vertex grips or arc segment grips, you cannot add a new vertex by hovering over them2. Therefore, the statement is false.
NEW QUESTION # 29 
You have a line segment that is 150 units long as shown in the exhibit.
You need the line to be 200 units long without adding any additional linework. The leftmost end of the line must remain in the current position.
What should you do?
- A. From the Project option of the Extend command, enter 50 units, and then select the right end of the line.
- B. From the Delta option of the Lengthen command, enter 50! units and then select the right end of the line
- C. From the Delta option of the Lengthen command, enter 200 units and then select the right end of the line
- D. From the Edge Extension option of the Extend command, enter 50 units, and then select the right end of the line
Answer: B
Explanation:
Explanation
From the Delta option of the Lengthen command, enter 50 units and then select the right end of the line. This way, you can increase the length of the line by 50 units from its current endpoint without changing its direction or position2
https://www.learnvern.com/autocad-tutorial-in-hindi/how-to-use-lengthen-command
NEW QUESTION # 30
Refer to the exhibit.
You are working on a drawing. You copy a set of entities and exit the COPY command. You then use the MOVE command on the same set of entities.
Which default option should you use when prompted to select entities?
- A. P (Previous)
- B. Spacebar
- C. L (Last)
- D. A (All)
Answer: A
Explanation:
Explanation
when you use the MOVE command on a set of entities that you have previously copied, you should use B. P (Previous) as the default option when prompted to select entities. This will select the last set of entities that you modified with any command.
https://forums.autodesk.com/t5/autocad-forum/move-previous-command/td-p/3466896
https://www.cadlinecommunity.co.uk/hc/en-us/articles/360002360178-Move-Copy-Rotate-All-in-one-editing-co
NEW QUESTION # 31
When you create an attribute definition, which mode should be used if you want the default value of the attribute assigned upon insertion where the attribute value cannot be changed?
Note Exhibit shown is the AutoCAD interface in Windows While the AutoCAD for Mac version differs in appearance, the correct answer correlates in the options.
- A. Lock position
- B. Preset
- C. Constant
- D. Verify
Answer: C
Explanation:
Explanation
the mode that should be used if you want the default value of the attribute assigned upon insertion where the attribute value cannot be changed is Constant. This option sets the attribute value as constant and prevents it from being modified during a block insertion or later.
https://knowledge.autodesk.com/support/autocad/learn-explore/caas/CloudHelp/cloudhelp/2015/ENU/AutoCAD
NEW QUESTION # 32
A site plan was recently modified to relocate a building to a new location While relocating the building, only the hatch location of the building was moved by mistake as shown in the exhibit.
Evaluate the graphic and answer each question by selecting the correct options from the drop-down lists.
Answer:
Explanation:
Explanation
Box 1 = Turn on Associative Hatching
Box 2 = use the Recreate Boundary option from Hatch Editor
https://knowledge.autodesk.com/support/autocad/troubleshooting/caas/sfdcarticles/sfdcarticles/Recreating-hatch-
https://knowledge.autodesk.com/support/autocad/learn-explore/caas/CloudHelp/cloudhelp/2018/ENU/AutoCAD
NEW QUESTION # 33
In the Layer Properties Manager, which column should you use to prevent a layer from being displayed in the active viewport only?
- A. VP Freeze
- B. VP Plot
- C. Freeze
- D. On
Answer: A
Explanation:
Explanation
The column you should use in the Layer Properties Manager to prevent a layer from being displayed in the active viewport only is "VP Freeze". The VP Freeze column allows you to control the visibility of layers in specific viewports. When you freeze a layer in the VP Freeze column, it is only hidden in the active viewport and remains visible in other viewports. On the other hand, when you freeze a layer with the Freeze column, it becomes hidden in all viewports. Therefore, VP Freeze is the column you should use to hide a layer in a specific viewport only.
https://help.autodesk.com/cloudhelp/2015/ENU/AutoCAD-LT/files/GUID-B297EBD9-D68C-47E1-87CE-1B37
NEW QUESTION # 34
What should be typed at the command line in order to start creating a line for drawing reference that starts at a defined point and extends to infinity in the designated direction?
- A. XLINE
- B. CURSORSIZE
- C. RAY
- D. MLINE
Answer: A
Explanation:
Explanation
According to the AutoCAD for Design and Drafting documents1, the command that should be typed at the command line in order to start creating a line for drawing reference that starts at a defined point and extends to infinity in the designated direction is XLINE2. This command creates a construction line, which is a type of reference line that can help you manage accurate parameters of your drawing2. You can also use point objects as nodes or reference geometry for object snaps and relative offsets3.
NEW QUESTION # 35
Refer to the exhibit.
When working on this part created with AutoCAD solids, the dimensions of the shaded planes need to be established.
Which U'CS shows the correct size and shape of the shaded planes?
- A. Vertical
- B. Face
- C. View
- D. World
Answer: B
Explanation:
Explanation
The UCS is a moveable Cartesian coordinate system that establishes the XY work plane, horizontal and vertical directions, axes of rotation, and other useful geometric references1. You can change the UCS origin and orientation for convenience as you specify points, enter coordinates, and work with drawing aids1.
The face option sets a new UCS based on a selected face of a 3D solid object2. This option will align the XY plane of the UCS with the selected face and show its correct size and shape2.
NEW QUESTION # 36
You need to change the width of a specific polyline without affecting the width of the other polylines in a drawing.
What should you use?
- A. The PEDIT command
- B. The PLINEWID system variable
- C. The LWEIGHT command
- D. The PLINEGEN system variable
Answer: A
Explanation:
Explanation
polyline is a connected sequence of line segments created as a single object that can contain a width. You can change the width of a polyline by using the PEDIT command.
Based on 3 and 4, LWEIGHT is a command that sets the current lineweight, which is used for new objects and affects objects in the current space only. PLINEWID is a system variable that sets a default polyline width for new polylines. PLINEGEN is a system variable that controls how linetype patterns are generated around vertices.
https://www.roadlesstraveledstore.com/how-do-i-change-the-width-of-a-polyline-in-autocad/
https://knowledgeburrow.com/how-do-i-change-the-width-of-a-polyline-in-autocad/
NEW QUESTION # 37
Refer to the exhibit.
The exhibit shows a set of ornamental garden stairs going up to a walkway as part of a landscaping design.
You need to make sure that the edge of the top step in shown in a different linetype, as shown by the dashed line in the exhibit.
Which prompt in the OFFSET command should you use?
- A. Erase
- B. Through
- C. Source
- D. Current
Answer: D
Explanation:
Explanation
The Current prompt should be used to make sure that the edge of the top step is shown in a different linetype, as shown by the dashed line in the exhibit. This way, you can set a different linetype for your current layer before using the OFFSET command4.
https://knowledge.autodesk.com/support/autocad/learn-explore/caas/CloudHelp/cloudhelp/2021/ENU/AutoCAD
NEW QUESTION # 38
You are using the UCS command to set the user coordinate system (UCS)
Select whether each statement is True or False.
Answer:
Explanation:
Explanation
* TrueAccording to 1 and 2, UCS is a command that sets the user coordinate system (UCS) which establishes the XY work plane and Z-axis direction for drawing and modeling.
Based on 1, you can use the View option to align the UCS with the current view orientation. This option rotates the UCS so that it matches your current view of a 3D model.
https://knowledge.autodesk.com/support/autocad/learn-explore/caas/CloudHelp/cloudhelp/2016/ENU/AutoCAD
* Falseccording to 1 and 2, UCS is a command that sets the user coordinate system (UCS) which establishes the XY work plane and Z-axis direction for drawing and modeling.
Based on 1, you can use the World option to set the UCS back to its default orientation. This option resets the UCS so that it matches the WCS (world coordinate system).
https://knowledge.autodesk.com/support/autocad/learn-explore/caas/CloudHelp/cloudhelp/2016/ENU/AutoCAD
* TrueAccording to 1 and 2, UCS is a command that sets the user coordinate system (UCS) which establishes the XY work plane and Z-axis direction for drawing and modeling.
Based on 1, you can use the Named option to save or restore named UCS definitions. This option allows you to create custom UCSs and switch between them easily.
https://knowledge.autodesk.com/support/autocad/learn-explore/caas/CloudHelp/cloudhelp/2016/ENU/AutoCAD
NEW QUESTION # 39
Exhibit
This image needs to be reproduced in AutoCAD. The wall and plaster lines need to be on separate layers.
After drawing the top wall line on the wall layer, then selecting it, what two options in the Offset (OFFSET) command should be used to offset and place the resulting lines on the plaster layer? (Choose two.)
- A. Select Layer
- B. Specify Offset Distance
- C. Select Object
- D. Select Current
Answer: A,B
Explanation:
Explanation
The offset command is used to create parallel lines, concentric circles, and parallel curves1. To use the offset command, you need to specify the offset distance and select the object that you want to offset23.
NEW QUESTION # 40
One of the lines in the drawing is at a 30 degree angle. What's the quickest way to align the X-axis of the UCS to that line?
- A. Modify the properties of the UCS icon from Properties palette.
- B. Start the UCS command and enter a coordinate.
- C. Start the UCSBASE command and set the new value
- D. Right-click the UCS icon, click Object, and then select an object in the drawing as the location.
Answer: D
Explanation:
Explanation
UCS is a command that sets a new user coordinate system (UCS) by specifying points or by selecting an object. You can use the Object option to align the UCS with a selected object such as a line.
Based on 3 and 4, UCSBASE is a system variable that sets the name of the current UCS base. PLINEGEN is a system variable that controls how linetype patterns are generated around vertices. LWEIGHT is a command that sets the current lineweight, which is used for new objects and affects objects in the current space only.
https://knowledge.autodesk.com/support/autocad/learn-explore/caas/CloudHelp/cloudhelp/2016/ENU/AutoCAD
https://knowledge.autodesk.com/support/autocad/learn-explore/caas/CloudHelp/cloudhelp/2020/ENU/AutoCAD
NEW QUESTION # 41
Drawings from different sources have been combined and resulted in duplicate background elements that are slightly offset from each other Some of the layer names match and other layers have an E prefix, indicating that they are existing.
To clean up the drawing, the Overkill (OVERKILL) command is used.
Which two settings will resolve the duplicate background and offsetting issues? (Select 2)
- A. Tolerance value
- B. Ignore Layer object property
- C. Ignore Transparency
- D. Ignore Color object property
- E. Maintain associative objects
Answer: A,B
Explanation:
Explanation
You need to ignore layer object property to remove duplicates that have different layer names but are otherwise identical4. You also need to set a tolerance value that is larger than the offset distance between the objects5.
NEW QUESTION # 42
You are modifying an AutoCAD drawing for a customer.
You would like to bring your customers attention to a specific area of the drawing that you modified for review.
Which type of object is conventionally used?
- A. A viewport
- B. A construction line
- C. A revision cloud
- D. A solid hatch
Answer: C
Explanation:
Explanation
The type of object that is conventionally used for this purpose is D. A revision cloud123. A revision cloud is a way to highlight changes or revisions in a drawing by creating a cloud-shaped polyline around them12. You can create a revision cloud by moving the mouse or by converting existing objects2. You can also change the style, color, layer and properties of the revision cloud13.
NEW QUESTION # 43
Refer to the exhibit.
The exhibit shows a plan view of an office arrangement. There is also a table of area of each room areas, which displays the area of each room highlighted with a bold polyline.
The room number labels in the plan are denoted by blocks; made up of a rectangle and a room number attribute.
Which entity in the drawing is used to put the graphical representation of the room number in the Room No.
column in the table?
- A. Single line text
- B. Block
- C. Rectangle and text
- D. Attribute
Answer: D
Explanation:
Explanation
a block attribute is a tag or label that attaches data to a block. The data can be extracted and displayed in a table. Therefore, the entity in the drawing that is used to put the graphical representation of the room number in the Room No. column in the table is B. Attribute.
http://autocadtip.com/how-to-create-block-attribute-in-autocad.html
NEW QUESTION # 44
With an associative array selected as shown in the exhibit, which command will separate the objects into individual objects?
- A. Disassociate
- B. Break
- C. Explode
- D. Ungroup
Answer: C
Explanation:
Explanation
array items are contained in a single array object, similar to a block. You can change the number of these items and their spacing in an associative array.
Based on 2, you can move an item in an associative array by pressing and holding the Ctrl key, and then selecting the items you want to move.
since explode is the command that separates objects into individual objects. Disassociate, ungroup and break are not valid commands for associative arrays.
https://knowledge.autodesk.com/support/autocad/learn-explore/caas/CloudHelp/cloudhelp/2020/ENU/AutoCAD
NEW QUESTION # 45
You plan to draw a line at an angle of 6.25 degrees.
Where in the user interface do you configure polar tracking to work at this angle after selecting Polar Tracking On?
Note: Exhibit shown is the AutoCAD interface in Wind. Which the AutoCAD for the Mac version differs in appearance, the correct answers correlate in the options.
Answer:
Explanation:
See the answer below:
Explanation
polar tracking is a feature that allows you to draw lines at specific angles. You can configure polar tracking to work at any angle you want by following these steps:
* Click on the arrow next to the Polar Tracking icon in the Status bar and select Settings.
* In the Drafting Settings dialog box, click on the Polar Tracking tab.
* Under Additional Angles, click on New and enter 6.25 as the angle value. Click OK.
* Make sure that 6.25 is checked in the list of additional angles. Click OK.
Now you can draw a line at an angle of 6.25 degrees by using polar tracking.
NEW QUESTION # 46
In model space (MODEL), a room label text height is set to 300 mm in the designated text style.
Which viewport scale should you apply to a layout viewport (PAPER) so that the room label text height will display as 3 mm when plotting the drawing?
- A. 1:1
- B. 100:1
- C. A custom viewport scale
- D. 1:100
Answer: B
Explanation:
Explanation
the formula for determining object scaling is:
Object Height x Annotation Scale x Annotation Plot Size = Model Space or Paper Space Height In this case, we want the room label text height to be 3 mm in paper space when plotting the drawing.
Assuming an annotation plot size of 1 mm and an object height of 300 mm, we can solve for the annotation scale as follows:
300 x Annotation Scale x 1 = 3 Annotation Scale = 3 / 300 Annotation Scale = 0.01 Therefore, the viewport scale that corresponds to this annotation scale is B. 100:1.
https://knowledge.autodesk.com/support/autocad-architecture/learn-explore/caas/CloudHelp/cloudhelp/2016/EN
NEW QUESTION # 47
You have three multileaders as shown in exhibit 1. (Refer to the exhibit 1 tab.)
You need to change the display of the multileaders to match the multileaders in exhibit. (Refer to the exhibit 2 tab.)
Which command should you use?
- A. Remove Leader
- B. Collect Leader
- C. Align Leader
- D. Add Leader
Answer: B
Explanation:
Explanation
The command that you should use is B. Collect Leader1. The collect leader option groups multiple leaders into one multileader object with a common landing line1. This option is useful when you want to create a single label or callout for multiple objects2.
To use this option, you need to select the MLEADER command and then select Collect Leader from the Options menu. Then you can select two or more existing multileaders that have similar properties and press Enter. The selected multileaders will be collected into one multileader object with a common landing line1.
NEW QUESTION # 48
......
Autodesk ACP-01101 is a globally recognized certification exam that evaluates an individual's skills in AutoCAD drafting and design. ACP-01101 exam is designed for professionals who want to showcase their expertise in using AutoCAD software to create and draft high-quality designs. Autodesk Certified Professional: AutoCAD for Drafting and Design certification exam is conducted by Autodesk, a leading software company that provides 3D design, engineering, and entertainment software.
Passing Key To Getting ACP-01101 Certified Exam Engine PDF: https://www.examcost.com/ACP-01101-practice-exam.html
ACP-01101 Exam Dumps Pass with Updated Tests Dumps: https://drive.google.com/open?id=1HQHKau40PlEv-Ekoq0xqH5mO62OM_9Bh
