Get Special Discount Offer on NACE-CIP2-001 Dumps PDF [UPDATED Jan-2023]
PDF Download NACE Test To Gain Brilliante Result!
NEW QUESTION 27
In powder coatings, when the particles of powder begin to flow but are not fully liquid, they are in what stage?
- A. Cure stage
- B. Gel stage
- C. Wetting stage
- D. Flow stage
Answer: D
NEW QUESTION 28
Steel shot grit contaminated with oil or grease used in a cetrifugal blast cleaning should be
- A. run through the air wash separator.
- B. washed with clean potable water prior to Use.
- C. mixed with uncontaminated abrasive
- D. disposed of properly.
Answer: D
NEW QUESTION 29
Differences in technique for abrasive blasting concrete versus steel require the operator to:
- A. Lower the blast pressure
- B. Increase the standoff distance
- C. a), b) and c)
- D. Move the nozzle quicker
Answer: C
NEW QUESTION 30
On pipelines, which coating is identifiable by its distinct colors, usually light blue, green, or grey?
- A. Liquid epoxies
- B. Heat-shrink sleeves
- C. Concrete
- D. Coal Tar Enamel
Answer: A
NEW QUESTION 31
When conducting inspections the Inspector should follow which standards:
- A. ISO standards in Europe and Asia
- B. NACE and SSPC standards in North America
- C. Australian standards in Australia
- D. The specified standards
Answer: D
NEW QUESTION 32
You are a NACE Level 2 Coating Inspector who has just arrived on a job in progress where there is no Inspection and Test Plan (ITP). The first morning you arrive the job is behind schedule and you are asked to take DIY Film Thickness readings.
Your FIRST preferred course of action is to:
- A. Develop your own methodology and proceed take the readings
- B. Refuse to take readings until an is in place
- C. Call your supervisor
- D. Use a generally accepted industry standard and to take readings
Answer: D
NEW QUESTION 33
You are NACE Level 2 Inspector working on a tank lining job where a mobile centrifugal blast unit is being used to blast the tank floor to a NACE No.1/SSPC SP 5. The Contractor has completed his final blast and has called for a hold point inspection. This is the 1 st time you have seen field based centrifugal blast cleaning. You observe what appears to be staining on the substrate however the Contractor assures you this is normal when using centrifugal blast units and what you are seeing is what is defined in the standard as an acceptable variation in appearance.
Your FIRST preferred course of action is to:
- A. Shut the job down
- B. Review the standard with the Contractor and re-inspect the floor
- C. Request that the Contractor re-blast the floor
- D. Call your supervisor
Answer: B
NEW QUESTION 34
Because a NACE Level 2 Inspector has been trained in specific destructive tests, it is up to the Inspector to decide if and when a destructive test is required.
- A. True
- B. False
Answer: B
NEW QUESTION 35
Coating surveys may include which steps?
Select All That Apply:
- A. Schedule the remedial work
- B. Evaluate the coatings performance
- C. Summarize the collected data
- D. Develop a survey plan
Answer: A,B,C,D
NEW QUESTION 36
You are working as the only in-house NACE Level 2 Inspector in a shop setting when an independent 3 rd party NACE Level 3 Inspector, representing the owner, presents you with a copy of a Non Conformance Report (NCR) he has written for a NACE2/SSPC SP 10 centrifugal blast which you had previously approved.
Your FIRST preferred course of action is to:
- A. Consult your supervisor
- B. Review the NCR with the other Inspector
- C. Request a re-blast of the item in question
- D. Verbally challenge the NCR
Answer: A
NEW QUESTION 37
When ASIN D 3363 is specified the Inspector must:
- A. Use the correct solvent
- B. Record the percentage of failure
- C. Record the highest value attained
- D. Record the two end points identified in the standard
Answer: D
NEW QUESTION 38
You are working as an inspector in a galvanizing plant for the first time.
What are some of the hazards you need to be aware of:
- A. Risk of skin
- B. Risk of chemical exposure
- C. a), b), and c)
- D. Risk of acid or caustic splashes
Answer: C
NEW QUESTION 39
The cost of qualified Coating Inspection is normally offset by:
- A. Lower Supervision Costs
- B. Lower Application Costs
- C. Lower Coating Life Cycle Costs
- D. Lower Safety Enforcement Costs
Answer: C
NEW QUESTION 40
The HATE adhesion tester uses
- A. a hydraulic piston to apply pressure to the test dolly.
- B. mechanical means only to apply pressure to the test dolly.
- C. a special tape to apply pressure to the test dolly.
- D. compressed air to apply pressure to the test dolly.
Answer: A
NEW QUESTION 41
You can use magnifiers to examine all of the following EXCEPT
- A. Mill scale
- B. Surface profile
- C. Blisters
- D. Surface cleanliness
Answer: D
NEW QUESTION 42
Individuals conducting Coating Surveys should:
- A. Always be experienced Specification Writers
- B. Always be NACE or SSPC Protective coating Specialists
- C. Always be trained and experienced Coating Industry
- D. Always be NACE Level 3 Certified Inspectors
Answer: C
NEW QUESTION 43
When using a destructive Paint Inspection Gauge the NACE inspector must:
- A. Determine the Dry Film Thickness of the coating prior to use
- B. Ensure the glue on the dolly is properly applied prior to use
- C. Select the appropriate hand wheel based on the measured Dry Film Thickness prior to us
- D. Consult SSPC Guide 1 prior to use
Answer: A
NEW QUESTION 44
Which type of pipelines collect the gas from the transmission system so utility companies can distribute the gas to end users?
- A. Transmission
- B. Distribution
- C. Midstream
- D. Gathering
Answer: B
NEW QUESTION 45
You are the NACE Inspector on a project where a stationary floating structure is being coated and you notice a self-smoothing anti-fouling coating has been specified.
This is not a good choice because:
- A. The floating structure is stationary
- B. It doesn't contain biocide
- C. It will result in a very slippery surface
- D. It contains biocide
Answer: D
NEW QUESTION 46
NACE/SSPC Water Jetting standards are directly equivalent to ISO Abrasive Blast Standards:
- A. True
- B. False
Answer: B
NEW QUESTION 47
Inspection and Test plans are developed by referencing:
- A. The Specification, Safety Manual, Relevant Standards and Codes
- B. The Specification, Application Guidelines, 'Relevant Standards and Codes
- C. The Specification, SDS, relevant Standards and Codes
- D. The Specification, TDS, relevant Standards and Codes
Answer: D
NEW QUESTION 48
Inspectors perform tests on linings that they may not perform on exterior coatings because
- A. coatings are more durable than linings.
- B. linings protect the contents and the container.
- C. linings are more durable than coatings.
- D. coatings are expected to degrade over time.
Answer: B
NEW QUESTION 49
When completing the Final Inspection report the Inspector should write the report using:
- A. Language that the most would understand
- B. Language that only technical experts would understand
- C. Language that only in the project would understand
- D. Language that another NACE Inspector would understand
Answer: A
NEW QUESTION 50
......
NACE-CIP2-001 Dumps are Available for Instant Access: https://www.examcost.com/NACE-CIP2-001-practice-exam.html
Provide Updated NACE NACE-CIP2-001 Dumps as Practice Test and PDF: https://drive.google.com/open?id=1yUevo2HA9BCE1DX_6O_WakG0wgKPrDvS
