Verified & Correct JN0-352 Practice Test Reliable Source Aug 12, 2026 Updated [Q16-Q36]

Share

Verified & Correct JN0-352 Practice Test Reliable Source Aug 12, 2026 Updated

Free Juniper JN0-352 Exam Files Downloaded Instantly

NEW QUESTION # 16
You are deploying a trunk port with multiple VLANs. In this scenario, which statement is true about the native VLAN?

  • A. The native VLAN is automatically configured through DHCP.
  • B. The native VLAN is the highest tagged VLAN ID on the port.
  • C. The native VLAN is an untagged VLAN ID on the port.
  • D. The native VLAN must be the default VLAN on the port.

Answer: C


NEW QUESTION # 17
Which two statements are correct about martian routes? (Choose two.)

  • A. Martian routes only represent publicly used prefixes.
  • B. Martian routes are always host addresses.
  • C. Additional prefixes can be added to the list of martian routes.
  • D. Martian routes are never installed in the route table.

Answer: C,D

Explanation:
Martian routes are never installed in the route table.
Martian routes refer to IP addresses or prefixes that are considered invalid or reserved, and they are not installed in the routing table.
Additional prefixes can be added to the list of martian routes.
Network administrators can configure the system to treat additional prefixes as Martian routes based on specific network policies or requirements.


NEW QUESTION # 18
Which two elements are used to create the STP bridge ID? (Choose two.)

  • A. the system MAC address
  • B. the root port number
  • C. the port cost
  • D. the bridge priority value

Answer: A,D


NEW QUESTION # 19
You have two OSPF routers that will not form an adjacency. You enter the show log trace- ospfcommand.
Referring to the exhibit, which statement is correct?

  • A. There is a mismatched subnet.
  • B. You are stuck in the ExStart state.
  • C. The physical connection has been disconnected.
  • D. The wrong OSPF area has been configured.

Answer: D


NEW QUESTION # 20
Which statement about configuring persistent MAC learning is correct?

  • A. Persistent MAC learning can be configured on access mode interfaces.
  • B. Persistent MAC learning requires 802.1X authentication.
  • C. Persistent MAC learning flushes dynamically learned MAC addresses on reboots.
  • D. Persistent MAC learning cannot be configured on redundant trunk groups.

Answer: A


NEW QUESTION # 21
Which two statements correctly describe RSTP port roles? (Choose two.)

  • A. The backup port is used as a backup for the root port.
  • B. The root port is responsible for forwarding data to the root bridge.
  • C. The alternate port is a standby port for an edge port.
  • D. The designated port forwards data to the downstream network segment or device.

Answer: B,D

Explanation:
An RSTP topology contains ports that have specific roles:
The root port is responsible for forwarding data to the root bridge.
The alternate port is a standby port for the root port. When a root port goes down, the alternate port becomes the active root port.
The designated port forwards data to the downstream network segment or device.
The backup port is a backup port for the designated port. When a designated port goes down, the backup port becomes the active designated port and starts forwarding data.


NEW QUESTION # 22
The ISP1.inet.0 route table has currently no routes in it.
What will happen when you commit the configuration shown on the exhibit?

  • A. The inet.0 route table will be imported into the ISP1.inet.0 route table.
  • B. The ISP1.inet.0 route table will be completely overwritten by the inet.0 route table.
  • C. The ISP1.inet.0 route table will be imported into the inet.0 route table.
  • D. The inet.0 route table will be completely overwritten by the ISP1.inet.0 route table.

Answer: A

Explanation:
The configuration shown in the exhibit is an example of a routing instance of type virtual-router. A routing instance is a collection of routing tables, interfaces, and routing protocol parameters that create a separate routing domain on a Juniper device. A virtual-router routing instance allows administrators to divide a device into multiple independent virtual routers, each with its own routing table.
The configuration also includes a rib-group statement, which is used to import routes from one routing table to another. A rib-group consists of an import-rib statement, which specifies the source routing table, and an export-rib statement, which specifies the destination routing table. In this case, the rib-group name is inet-to-ispi, and the import-rib statement specifies inet.0 as the source routing table. The export-rib statement specifies ispi.inet.0 as the destination routing table.
This means that the routes from inet.0 will be imported into ispi.inet.0.


NEW QUESTION # 23
What is the default keepalive time for BGP?

  • A. 10 seconds
  • B. 90 seconds
  • C. 60 seconds
  • D. 30 seconds

Answer: D

Explanation:
The default hold-time is 90 seconds, meaning that the default frequency for keepalive messages is 30 seconds.
https://www.juniper.net/documentation/us/en/software/junos/bgp/topics/ref/statement/precision-timers-edit-protocols-bgp.html#:~:text=BGP%20on%20the%20local%20routing,keepalive%20messages%20is%2030
%20seconds


NEW QUESTION # 24
Refer to Exhibit:

R1 is not responding to ICMP requests sent to the VIP address.
Referring to the exhibit, which command option would you configure on the virtual address to correct this problem?

  • A. advertise-interval
  • B. accept-data
  • C. track
  • D. no-preempt

Answer: B

Explanation:
In this configuration, R1's physical interface address (10.10.10.1) is different from the VRRP virtual IP address (10.100.100.1), meaning R1 is operating as a non-owner VRRP master - it did not originate the virtual address as one of its own real interface addresses. By default, Junos VRRP masters that do not own the virtual address will forward transit traffic destined through that address but will not process or respond to traffic addressed directly to the VIP itself, such as ICMP echo requests, Telnet, or SSH sessions aimed at
10.100.100.1. This is deliberate default behavior intended to prevent ambiguity about which physical device is answering on behalf of a shared virtual identity. To allow the master to accept and respond to packets whose destination is the virtual address itself, the accept-data statement must be explicitly configured under the vrrp- group hierarchy. Once enabled, the elected master will process locally destined traffic sent to the VIP, resolving exactly the symptom described. The track option is used for interface or route-based priority adjustment to influence mastership, advertise-interval tunes the frequency of VRRP hello advertisements, and no-preempt prevents a higher-priority router from reclaiming mastership once a lower-priority router has taken over - none of these affect whether the master processes traffic destined to the VIP. Reference topics:
Junos Enterprise Routing - High Availability, VRRP accept-data Behavior.


NEW QUESTION # 25
Which two statements describe the purpose of a BGP notification message? (Choose two.)

  • A. It reports the specific reason why the session must end.
  • B. It refreshes the neighbor's routing table without resetting the session.
  • C. It updates route attributes and keeps the session active.
  • D. It ends the BGP session when a fatal error is detected.

Answer: A,D

Explanation:
A BGP NOTIFICATION message is one of the four core message types defined in RFC 4271, alongside OPEN, UPDATE, and KEEPALIVE, and it serves a very specific and narrow purpose within the protocol:
whenever a BGP speaker detects an unrecoverable, fatal condition in the session - such as a malformed OPEN message, an unsupported capability, a hold-timer expiration, a finite-state-machine error, or an administratively initiated reset - it transmits a NOTIFICATION message to its peer immediately before closing the underlying TCP connection and tearing down the session entirely. This confirms that a NOTIFICATION always signals the termination of the session upon a fatal error, never a routine, in-session update. Structurally, every NOTIFICATION message carries a defined error code and error subcode field, which together precisely classify the category and specific nature of the fault that triggered the termination (for example, 'Cease' with a subcode indicating administrative shutdown, or 'Update Message Error' with a subcode indicating a malformed attribute), giving the receiving peer's administrator concrete diagnostic information about exactly why the session was torn down. Updating route attributes while keeping a session alive is the role of the UPDATE message, not NOTIFICATION, and refreshing a neighbor's table without resetting the session describes the optional Route Refresh capability (a separate, distinct BGP mechanism), neither of which describes NOTIFICATION's function. Reference topics: Junos Enterprise Routing - BGP, BGP Message Types and the NOTIFICATION Message.


NEW QUESTION # 26
Which IS-IS PDU should be used by a router to list all LSPs that it believes should exist in the link-state database?

  • A. IIH
  • B. PSNP
  • C. LSP
  • D. CSNP

Answer: D

Explanation:
The Complete Sequence Number PDU (CSNP) is the IS-IS mechanism used to summarize the entire contents of a router's link-state database, listing the LSP ID, sequence number, checksum, and remaining lifetime for every LSP the sending router currently believes should exist in the database for that level. On broadcast (LAN) circuits, the elected Designated Intermediate System periodically transmits CSNPs to all routers on the segment as a database-synchronization mechanism; any receiving router compares the summarized list against its own local database, and any discrepancy - an LSP it is missing entirely, or one for which it holds an older sequence number - triggers a targeted request for the specific, updated LSP content. On point-to-point circuits, a single CSNP is exchanged once when the adjacency first comes up, serving the identical synchronization purpose without needing periodic repetition. The Partial Sequence Number PDU (PSNP), by contrast, is used to acknowledge receipt of specific LSPs or to explicitly request specific LSPs identified as missing or outdated after a CSNP comparison, making it a partial, targeted PDU rather than a complete database listing. The LSP itself is the PDU that actually carries the detailed topology and reachability information being advertised, rather than a database summary. The IS-IS Hello PDU (IIH) is used purely for neighbor discovery and adjacency maintenance and carries no link-state database summary information whatsoever. Reference topics: Junos Enterprise Routing - IS-IS, CSNP and Link-State Database Synchronization.


NEW QUESTION # 27
Which statement describes how nonstop active routing (NSR) maintains routing protocol information during a Routing Engine switchover?

  • A. The backup Routing Engine continuously synchronized protocol states by running the RPD process.
  • B. The Packet Forwarding Engine updates protocol state based on the most recent LSA or BGP update received.
  • C. The backup Routing Engine retrieves routing information from neighboring routers after a switchover.
  • D. The primary Routing Engine copies protocol information only when an NSR event begins.

Answer: A

Explanation:
Nonstop active routing's defining architectural feature is that the backup Routing Engine runs a fully live, active instance of the routing protocol daemon (rpd) in parallel with the primary Routing Engine's rpd instance, continuously, from the moment NSR and its prerequisite GRES are established - not merely at the instant a switchover begins. As protocol adjacencies form, routes are learned, and the RIB is updated on the primary Routing Engine, that same protocol and RIB state is mirrored in real time to the backup Routing Engine's rpd process through an internal synchronization mechanism, so the backup's protocol state remains a live, up-to-date replica of the primary's at essentially every moment during normal operation. When a switchover occurs, the backup Routing Engine simply assumes the primary role with protocol adjacencies, routing tables, and forwarding state already fully populated and current, allowing it to continue operating without re-establishing neighbor relationships or re-learning the network topology, which is what makes the switchover genuinely nonstop and invisible to neighboring routers. This is fundamentally different from graceful restart, where the restarting router must rebuild its state by requesting help from cooperating neighbors after the fact. The Packet Forwarding Engine plays no role in synchronizing protocol-layer information such as LSAs or BGP updates; that is strictly an rpd-to-rpd function coordinated through the Routing Engine synchronization infrastructure. Reference topics: Junos Enterprise Routing - High Availability, Nonstop Active Routing Architecture and rpd Synchronization.


NEW QUESTION # 28

Click the Exhibit button.
Devices on VLAN 5 and VLAN 7 need to communicate with each other.
Referring to the exhibit, what will satisfy this requirement?

  • A. Enable spanning tree on both VLANs and set the EX Series Switch as the root bridge.
  • B. Add both VLANs to a single trunk port and enable the Multiple VLAN Registration Protocol.
  • C. Configure a family inet interface connecting the two VLANs and assign both subnet IPs to it using secondary addressing.
  • D. Create an integrated routing and bridging (IRB) interface for each VLAN, assign the gateway IP to each IRB, and enable static routing.

Answer: D

Explanation:
VLAN 5 and VLAN 7 are two entirely separate Layer 2 broadcast domains, each with its own distinct IP subnet, and devices in one VLAN can never reach devices in the other through switching alone - Layer 3 routing between the two subnets is mandatory for any inter-VLAN communication to occur, regardless of how the VLANs are configured at Layer 2. On a single EX Series switch, the correct and standard mechanism for enabling this routing without an external router is to create one integrated routing and bridging (IRB) logical interface for each VLAN, assign each IRB the appropriate gateway IP address for its respective subnet (192.168.5.1 for VLAN 5's irb.5 and 192.168.7.1 for VLAN 7's irb.7, for example), and ensure routing is active on the switch so that traffic arriving at one IRB's gateway address destined for the other VLAN's subnet is routed internally between the two IRB interfaces. Attempting to bind a single family inet interface with two distinct subnet addresses via secondary addressing conflates two separate broadcast domains onto one Layer 3 interface incorrectly and is not how VLAN routing is architected in Junos. Spanning tree exists purely to prevent Layer 2 loops and has no routing function whatsoever, so configuring it cannot enable inter-VLAN reachability. Placing both VLANs on a single trunk with Multiple VLAN Registration Protocol (MVRP) only automates VLAN membership propagation across trunk links; it does not provide any Layer 3 routing capability between the VLANs either. Reference topics: Junos Enterprise Switching - Routing VLANs, Configuring IRB Interfaces for Inter-VLAN Routing.


NEW QUESTION # 29
Which statement is correct about how a Juniper Networks EX Series Switch learns MAC addresses?

  • A. The switch learns MAC addresses only after a spanning-tree topology change occurs.
  • B. The switch learns MAC addresses by polling connected hosts periodically.
  • C. The switch adds destination MAC addresses to the bridge table after forwarding frames.
  • D. The switch learns source MAC addresses from received frames and records the ingress interface and timestamp.

Answer: D

Explanation:
Layer 2 MAC learning on an EX Series switch, as on any standard Ethernet bridge, is a passive, frame-driven process rather than an active polling or query-based mechanism. Every time a frame arrives on any interface, the switch inspects the frame's source MAC address field and, if that address is not already present in the Ethernet switching (bridge) table for the associated VLAN, creates a new dynamic entry recording the source MAC address, the VLAN it was learned on, and the specific ingress interface through which the frame arrived. Junos also stamps each learned entry with an aging timestamp, which is refreshed every time a subsequent frame from that same source MAC is received; entries that receive no refreshing traffic within the configured MAC aging interval (300 seconds by default) are eventually purged from the table to keep it current and to reclaim table space from hosts that have moved or gone offline. This source-address-driven, per-frame learning process happens continuously and automatically with no dependency on spanning-tree state changes - although a topology change notification can trigger accelerated aging of the table to flush potentially stale entries faster, learning itself is not gated by or contingent upon such an event occurring. The switch never learns addresses from the destination field of a frame, since the destination address, if already known, is used purely for the forwarding lookup decision, not for populating new table entries. Reference topics: Junos Enterprise Switching - Layer 2 Switching Fundamentals, Source MAC Learning and Table Aging.


NEW QUESTION # 30
Which statement describes the purpose of an integrated routing and bridging (IRB) interface on a Juniper Networks EX Series Switch?

  • A. It removes the need for routing instances.
  • B. It performs Layer 2 switching across multiple VLANs.
  • C. It provides a Layer 3 gateway for a specific VLAN.
  • D. It replaces the need for trunk ports.

Answer: C

Explanation:
An integrated routing and bridging interface, configured as irb.x on an EX Series switch, is the mechanism that bridges the Layer 2 and Layer 3 forwarding planes for a given bridge domain or VLAN. By assigning an irb logical unit to a VLAN and configuring an IP address on that unit, the switch gains a routable Layer 3 gateway address that hosts within that VLAN can use as their default gateway, enabling traffic destined for other subnets to be routed off the local broadcast domain. Internally, when a frame destined for the gateway's MAC address arrives on any port belonging to that VLAN, the switch's integrated circuitry hands the packet from the Layer 2 bridging domain to the Layer 3 routing engine associated with the corresponding irb interface, and vice versa for the return path - hence the name 'integrated routing and bridging.' IRB does not eliminate the need for routing instances, which remain a separate mechanism for isolating routing tables; it does not itself perform inter-VLAN switching, since switching still happens strictly within a VLAN's own broadcast domain; and it has no relationship to trunk ports, which remain necessary for carrying multiple tagged VLANs between switches. IRB is the standard method for enabling inter-VLAN routing on a single EX Series switch without an external router. Reference topics: Junos Enterprise Switching - Routing VLANs, Configuring Integrated Routing and Bridging.


NEW QUESTION # 31
You have configured a GRE interface, but no traffic will flow.
Referring to the exhibit, which statement is true?

  • A. The gr-1/2/0 interface is an invalid GRE interface.
  • B. The IP subnet mask cannot be a /32.
  • C. The source and destination addresses cannot have the same third octet.
  • D. The unit number cannot be 0.

Answer: B


NEW QUESTION # 32
Depending on the link type, OSPF sends link-state update packets to which two addresses? (Choose two.)

  • A. 224.0.0.6
  • B. 224.0.0.9
  • C. 224.0.0.8
  • D. 224.0.0.5

Answer: A,D

Explanation:
OSPF relies on two IANA-reserved multicast addresses to distribute its control-plane traffic across broadcast and NBMA network types, and Link State Update (LSU) packets, which carry the actual LSAs being flooded, are addressed to one or the other depending on the role of the sending router. The address 224.0.0.5, designated AllSPFRouters, is used when any OSPF router - including a router that is itself the Designated Router or Backup Designated Router - needs to flood an LSU to every OSPF-speaking router on the segment; this is the address used for Hello packets universally and for LSU flooding directed at the entire segment. The address 224.0.0.6, designated AllDRouters, is used specifically by non-DR, non-BDR routers (DROthers) when they need to send an LSU or other update destined for the DR and BDR only, since only the DR and BDR actually listen on this address; the DR then takes responsibility for reflooding that information to the rest of the segment using 224.0.0.5. This two-address design is central to how OSPF achieves flooding efficiency on multi-access networks by funneling updates through the DR rather than requiring full-mesh flooding among every router pair. The addresses 224.0.0.8 and 224.0.0.9 are not used by OSPF at all;
224.0.0.9 is in fact reserved for RIPv2 multicast updates, making it a plausible-looking but incorrect distractor. Reference topics: Junos Enterprise Routing - OSPF, Multicast Addressing for Hello and Link State Update Packets.


NEW QUESTION # 33
What is the maximum allowable MTU size for a default GRE tunnel without IPv4 traffic fragmentation?

  • A. 1496 bytes
  • B. 1476 bytes
  • C. 1480 bytes
  • D. 1500 bytes

Answer: B

Explanation:
The maximum allowable MTU size for a default GRE tunnel without IPv4 traffic fragmentation is
1476 bytes. This is because GRE packets are formed by the addition of the original packets and the required GRE headers. These headers are 24-bytes in length and since these headers are added to the original frame, depending on the original size of the packet we may run into IP MTU problems. The most common IP MTU is 1500-bytes in length (Ethernet). When the tunnel is created, it deducts the 24-bytes it needs to encapsulate the passenger protocols and that is the IP MTU it will use. For example, if we are forming a tunnel over FastEthernet (IP MTU 1500) the IOS calculates the IP MTU on the tunnel as: 1500-bytes from Ethernet-24-bytes for the GRE encapsulation = 1476-Bytes.


NEW QUESTION # 34
Which two statements about BGP facilitate the prevention of routing loops between two autonomous systems? (Choose two.)

  • A. EBGP routers will prepend their AS number when advertising routes to their neighbors
  • B. EBGP routers will only accept routes that contain their own AS number in the AS_PATH.
  • C. EBGP routers will append their AS number when advertising routes to their neighbors.
  • D. EBGP routers will drop routes that contain their own AS number in the AS_PATH

Answer: C,D

Explanation:
When an EBGP router advertises a route to a neighbor in a different AS, it appends its own AS number to the AS_PATH attribute. This helps other routers recognize the path the route has taken and prevents routing loops.
If an EBGP router receives a route advertisement that already contains its own AS number in the AS_PATH attribute, it will drop the route. This prevents the router from accepting a route that would create a routing loop.


NEW QUESTION # 35
What are two purposes of an aggregate route? (Choose two.)

  • A. to decrease the number of route advertisements
  • B. to hide internal routes from external peers
  • C. to allow external peers to see internal routes
  • D. to increase the number of route advertisements

Answer: A,B


NEW QUESTION # 36
......

Pass Juniper JN0-352 exam Dumps 100 Pass Guarantee With Latest Demo: https://www.examcost.com/JN0-352-practice-exam.html